Re: WorkCentre 3325 scan to PC configuration problem
Hi Joe, I didn't remember this solution, thank you!
View ArticleRe: Workcentre 7435 - error 005-913 insists
Unfortunatelly, this didn't work. I tried 3 times. One with the printer off, one with the printer on, and the 3rd, I first put the card stock in the feeder, then I turned on the printer and followed...
View ArticleRe: Workcentre 7435 - error 005-913 insists
It is very much the sensor, and I have no idea how you would fix it or replace it without having a Xerox tech do it.Try finding a Service manual online and see if you can get it fixed on your own.
View ArticleClik here to view.
WorkCentre 6605 - Gmail scan
Hi, we tried to setup scan to e-mail with a Gmail account on a Xerox 6605 but it stucks on "processing...". We cannot delete the job and to make the printer work again we have to reboot it. These are...
View ArticleRe: WorkCentre 6605 - Gmail scan
Update to the latest firmware at this link and try again. If it doesn't work after the update, you would need to go through an intermediary server, something like SMTP2Go.
View ArticleFreeFlow Scanner 665 won't 3 hole fill
When scanning with the autofeeder, the hole fill function won't fill the top hole at all, and sometimes won't fill small portions of the outside of the bottom two holes. This seems to be a problem...
View ArticleRe: workCentre 6605 system password
Press & hold 2 & 8 while powering on in order to enter service mode on the Xerox 6605.
View ArticleRe: FreeFlow Scanner 665 won't 3 hole fill
Hi TCC2016, Thank you for using the Support Forum. Please take a look at the tips for using the hole fill feature. If these tips do not help please consider contacting your local support centre.
View ArticleClik here to view.
Xerox 3635 - SMTP issues using Exchange 2013
Hello Xerox Team,We've upgraded our Exchange server from 2010 to 2013.And we are now having issues while we are trying to get FAX forward to Email.We didnt change anything on our printer side. (Picture...
View ArticleRe: Xerox 3635 - SMTP issues using Exchange 2013
Impossible to answer without knowing a single thing beyond your server version. That said, Exchange 2013 tends to require Authentication, and the email address tends to have to be valid.It also tends...
View Articleproper queue name for a D136?
I have a very specific reason for needing to print from a Windows workstation to a D136 copier via the LPD protocol. When I send a test print using either 'lp; or 'PASSTHRU' the job doesn't print....
View ArticlePower loss after static jam in DADF - WC7970
WC7970 shut down and reset itself with no error message in the middle of a scan using the DADF.The fault code history reads as follows:305.916.00305.915.00305.907.00305.906.00303.777.00Looking up the...
View ArticleReplaced Transfer belt in Xerox workcentre 7125
Replaced the transfer belt in Xerox workcentre 7125 and now the copier only copies about half the page instead of just putting lines in it. Any help would be appreciated.
View ArticleRe: Power loss after static jam in DADF - WC7970
It's most likely just a glitch. There was a firmware level that could do a forced reboot (crash) while doing SMB scans to Server 2012. I can't remember what version, but it was a while ago, so it...
View ArticleClik here to view.
Re: proper queue name for a D136?
D136 changes queues depending on print controller. The built in is just lp (LP but lower case) assuming you have it turned on, if you don't, it can be done remote via CWIS >Properties >...
View ArticleRe: Replaced Transfer belt in Xerox workcentre 7125
Copies in the ADF as well as off the platen?How about internal pages like the configuration report which doesn't use any of the copy functionality?Is it all colors or just some?Does the half print...
View ArticleRe: proper queue name for a D136?
Thanks Joe! Thsi is actually a client's printer, so I don't have direct access to it. He checked the first screen below and LPD is checked. Not sure what you mean by Fiery and Freeflow? Should I be...
View ArticleRe: Replaced Transfer belt in Xerox workcentre 7125
fades out half way across the sheet like the copier isn't seeing the entire image. only copies. printing worked ok and faxes are good too. didn't matter if it was adf or platen
View ArticleRe: Replaced Transfer belt in Xerox workcentre 7125
Open the lid, make a copy of nothing (choose 11*17 as the original size)As the light bar goes across, watch if it goes out in places.
View ArticleRe: Replaced Transfer belt in Xerox workcentre 7125
light bar stays on all the way across
View Article